Advances in Cryogenic Engineering Materials

... ASD-TDR-62–794 Part 2, WrightPatterson Air Force Base, Ohio, March 1964 13 D W Chamberlain, Mechanical Properties Testing of Plastic Laminate Materials down to 20K, 1964 Cryogenic Engineering Conference, Philadelphia.(1964) 14.

Advances in Cryogenic Engineering Materials

"Since 1954 Advances in Cryogenic Engineering has been the archival publication of papers presented at the biennial CEC/ICMC conferences. Advances in Cryogenic Engineering resides throughout the world in the libraries of most institutions that conduct research and development in cryogenic engineering and applied superconductivity. The publication includes invited, unsolicited, and government-sponsored research papers in the research areas of superconductors and structural materials for cryogenic applications. All of the papers published must (1) be presented at the conference, (2) pass the review process, and (3) report previously unpublished theoretical studies, reviews, or measurements of material properties at low temperatures." Victoria A. Bardos, Managing Editor

Electrical Manufacturing

Methods for preparing such compounds and testing their mechanical properties were presented by C. L. Segal. ... Reinforced Plastics at 3000 Fahrenheit What happens to reinforced plastics laminates under combined effects of extended ...

Electrical Manufacturing


Plastics Monthly

urethane on nonwoven polyester substrate and on woven interlayer , and napped material on nonwoven substrate ; cross ... test apparatus for testing wet and dry gas permeation through plastic films or paper laminates ; data included for ...

Plastics Monthly


Mechanical World and Engineering Record

Polyurethane figure , as appropriate , and so control the laminate foam is a first choice material for sandwich ... This is born out by the test figures which show Table V. – POLYURETHANE FOAM SANDWICH very little increase in strength ...

Mechanical World and Engineering Record


Proceedings

Impact Strength : In Table I it is seen that , when tested by conventional impact test , GLASTIMAT is superior to ... is the value of 20,000 psi flexural strength at 130 ° C after one hour at 130 ° C , twice as strong as laminate . 3.

Proceedings


Scientific and Technical Aerospace Reports

Failure is assumed to initiate at the sharp 90 deg reentrant corner of the step - down geometry due to a rise in stresses ... The analysis assumes tangent modulus behavior of the elastic - plastic - strain hardening material , and makes ...

Scientific and Technical Aerospace Reports


Managing Corrosion with Plastics

This general term " equipment " can be further broken down to cover storage tanks , processing vessels with and without ... The first is a standardized material system with established sequence of reinforcement and physical properties ...

Managing Corrosion with Plastics


Materials Engineering

New pyrrone plastics withstand 500 F continuously Materials specialists at Langley Research Center have come up with a ... Laminates , which in 12 - ply glass reinforced form , have 90,000 - psi flex strength , 5 - million - psi modulus ...

Materials Engineering

Issues for 1929- include section Contents noted (1929-1939 called Metallurgical abstracts; Jan. 1940- Sept. 1945 called Engineering digest; Oct. 1945- called Materials & methods digest) Annual indexes of the abstracts and digest were prepared 1929-1941; beginning in 1942, included in the complete index to the periodical.

Metal Progress

PROGRESS IN PLASTICS materials today MATERIALSPROGRESS® in 300 - ton capacity testing machines , too ... Applied heat and pressure cure the tape , while retaining the unidirectional strength and stiffness characteristic of boron ...

Metal Progress


Handbook of Foamed Plastics

Mattresses is another example of how the properties of these new synthetics are used to advantage . ... Made of about 97 % air and 3 % plastic , they are being laminated to almost any material — even jerseys and lacy knits .

Handbook of Foamed Plastics


Saturday Review

The American Society for Testing and Materials , headquartered in Philadelphia , has just published in monograph form ... resistant plastic materials reinforced with structural glass - fiber laminates and assembled into a steel shell .

Saturday Review


Transactions The Society of Naval Architects and Marine Engineers

The steel mold The repairability of reinforced glass - fiber plastic was made for under $ 10,000 . boats cannot ... If a laminate shown , Type E , requires higher physical roll of cold cloth is brought into a warm room , it properties ...

Transactions   The Society of Naval Architects and Marine Engineers

List of members in vols. 1-24, 38-54, 57.

ASM Handbook Fatigue and fracture

0.007 0.007 0.006 0.006 1500 SCS - 6 / Ti - 15-3 ( 0/90/0 ) R = 0.1 Room temperature Matrix material Ti - 15-3 As ... Figure 28 shows a typical strong , thus sacrificing laminate strength by cludes the calculated thermal residual ...

ASM Handbook  Fatigue and fracture

These volumes cover the properties, processing, and applications of metals and nonmetallic engineering materials. They are designed to provide the authoritative information and data necessary for the appropriate selection of materials to meet critical design and performance criteria.

Insulation

Chemical Div . , Great American Plastics Co. , 85 Factory St. , Nashua , N.H. but can be used for limited periods at temperatures somewhat over 200 ° C . High dielectric strength and mechanical toughness are said to allow it to be ...

Insulation


Metals Abstracts

In addition to material costs , those of shaping , assembling , service , maintenance , repair and shut - down ... which increases sharply with temperature , above 20K the normal zone hardly grows beyond its initial size and the hot ...

Metals Abstracts